Pinagem

Pinagem ATtiny85 (DIP-8)

Pinos

1: PB5 (RESET / ADC0)
2: PB3 (XTAL1 / ADC3 / CLKI)
3: PB4 (XTAL2 / ADC2)
4: GND
5: PB0 (MOSI / AIN0 / OC0A / PCINT0)
6: PB1 (MISO / AIN1 / OC0B / PCINT1)
7: PB2 (SCK / ADC1 / T0 / INT0)
8: VCC

Especificações

Core	8-bit AVR
Tensão de alimentação	ATtiny85: 2.7–5.5 V; ATtiny85V: 1.8–5.5 V
Velocidade do clock	Up to 10 MHz at 2.7–5.5 V, 20 MHz at 4.5–5.5 V; internal 8 MHz RC oscillator
Memória flash	8 KB
SRAM	512 bytes
EEPROM	512 bytes
Pinos de E/S	6 (5 + RESET, usable as I/O if reset is disabled)
ADC	10-bit, 4 channels
Timers / PWM	Two 8-bit timers (Timer1 can run from a 64 MHz PLL); up to 3 PWM outputs in Arduino cores
Serial interfaces	USI (used for I2C or SPI in software); no hardware UART
Corrente CC por pino de E/S	40 mA absolute max; 200 mA total through VCC/GND
Operating temperature	−40–85 °C (industrial grade)
Encapsulamento	DIP-8, SOIC-8, QFN-20

Mais pinagens

Timer 555 (DIP-8)Tensão de alimentação: NE555: 4.5–16 V; CMOS TLC555: 2–15 V; ICM7555: 2–18 V; Supply current (no load): NE555: ≈ 3 mA typ at 5 V, ≈ 10 mA at 15 V; CMOS…
Inversor Schmitt-trigger sêxtuplo 74HC14 (DIP-14)Logic family: 74HC (high-speed CMOS); Gates: 6 Schmitt-trigger inverters; Tensão de alimentação: 2–6 V
Driver de linha RS-232 MAX232 (DIP-16)Tensão de alimentação: 4.5–5.5 V (single 5 V supply); Supply current: ≈ 8 mA typ (no load); Channels: 2 drivers + 2 receivers
Módulo RTC DS3231 (ZS-042, I2C)Tensão de alimentação: Chip: 2.3–5.5 V; module typically used at 3.3–5 V; Interface: I2C, up to 400 kHz; I2C address: 0x68 (RTC); 0x57 for the on-board…
Registrador de deslocamento 74HC595 (DIP-16)Logic family: 74HC (high-speed CMOS); Function: 8-bit serial-in, parallel-out with output latch and 3-state outputs; Tensão de alimentação: 2–6 V
Registrador de deslocamento de entrada paralela 74HC165 (DIP-16)Logic family: 74HC (high-speed CMOS); Function: 8-bit parallel-in, serial-out (QH plus inverted QH output); Tensão de alimentação: 2–6 V
ATmega328P (DIP-28)Core: 8-bit AVR; Tensão de alimentação: 1.8–5.5 V; Velocidade do clock: Up to 4 MHz at 1.8 V, 10 MHz at 2.7 V, 20 MHz at 4.5–5.5 V; internal 8 MHz RC…
Expansor de portas I2C PCF8574 (DIP-16)Tensão de alimentação: 2.5–6 V; Interface: I2C, 100 kHz (standard mode); I2C address: PCF8574: 0x20–0x27; PCF8574A: 0x38–0x3F (set by A0–A2)